Red RC » Accessories

August 19, 2020

LMR A319 series alloy & carbon rear hubs

Nemo Racing have introduced the new LMR aluminium and carbon fibre rear hub set for the Agama A319 and A319E. They feature adjustable height, arm position and a new longer link option on the carbon plate. The height adjustment inserts allow drivers to use three different heights, the lowest position is the standard position and then they can be raised in 2mm increments to a +4mm increase. The set includes two machined aluminium hubs, four carbon fibre camber link plates as well as mounting hardware.

Source: Nemo Racing [nemoracing.com]

August 19, 2020

Klinik RC Cougar 5 deg vertical ballstud caster blocks

Coming soon from Klinik RC are new 5 degree vertical ballstud caster blocks for the Schumacher Cougar Laydown and the forthcoming all-new Storm ST 2020 truck. Klink RC designed the caster blocks with the option of increasing front end grip, mechanical traction and steering response. With 0 washers these have the same geometry as a stock upright, adding washers will add initial steering response and increase corner speed. The parts will fit the Cougar Laydown, KC, KD and 2020 Storm racing truck kit.

View another image here

August 18, 2020

Tamiya TC-01 aluminium damper extenders

Tamiya have introduced a new option part for use with the TC-01 chassis in the form of aluminium damper extender. The parts replace the stock plastic part with aluminium posts, thereby contributing to a high-spec suspension setup and enhancing damper performance. The parts are machined from high-quality aluminium and they come blue anodised for wear and looks.

Source: Tamiya [tamiyausa.com]

August 18, 2020

Rêve D ASL front axle brass wheel spacers

Coming from Rêve D and made for their ASL front axles are new 2mm and 4mm brass wheel spacers. Both the 2mm and 4mm spacer weigh in at 1.98g with the different offset allowing to fine-tune the suspension track width. Using the brass spacers over the original, lightweight aluminium hexes will improve stability while diving into slow speed corners or holding the outside line of fast high speed corners. Both spacers are designed to interlock with the ASL axle and they are available separately as 2-piece sets.

View more images here

August 18, 2020

Yokomo BD10 short shock taper pistons

Coming from Yokomo and made for their BD10 touring car are new tapered 1.0mm 4-hole pistons. They feature a special, tapered design that provides different shock characteristics on compression and extension with the tapered shape resulting in quicker extension and increased “pack” upon compression. In addition the piston holes sit at an angle which means even when running softer oils the shocks offer a harder pack on quick inputs while absorbing micro vibrations and smaller road imperfections, keeping the wheels to the ground more effectively.

View another image here

August 18, 2020

RC Maker BD10 Slimflex chassis & weight options

RC Maker have introduced their new Slimflex carbon fibre chassis and floating electronics plate for the Yokomo BD10 touring car. Tested and developed for months the chassis will improve on the original chassis, especially in low-med traction conditions. The chassis is narrowed all round to provide less scrubbing in corners, leading to increased corner speed. This increases flex, so to counteract this, the designers have recessed the diff and spool cutouts instead of cutting them all the way through. Not only does this bring the chassis back up to the desired amount of flex, it also improves aerodynamic performance by not preventing air from under the chassis being forced up into the car, detrimental to downforce. Overall, the chassis is slightly stiffer than the kit chassis, and provides improved response.

Continue reading the report here

August 18, 2020

T-Works RC8B3.2 CVD driveshaft set

Coming from T-Works and made for the Team Associated RC8B3.2 and B3.1 is a CVD driveshaft set that is usable for both the front and the rear of the buggy. The dogbones and wheel axles are made of high-quality steel and they feature a black surface coating for wear resistance. The 94mm long driveshafts can be used both front and rear of the buggy and they fit the new B3.2 and older specification B3.1 alike.

Source: T-Works [rc-tworks.com]

August 17, 2020

T-Works RC8T DLC-coated shock shafts

Coming from T-Works are new DLC-coated shock shafts for the Associated RC8T truggy. Available in 57.8mm front and 66.8mm rear shafts, both types have been made of high-quality steel that has been given a DLC coating for a slick and rigid surface. The coating is usually used to protect the crankshafts of nitro engines, ensuring a very low wear and long durability of both the shock shafts and shock O-rings.

View the rear shock shafts here