Coming from T-Works are two new tungsten weights, in 10 and 5 grams. The use of the heavy material allows for a low profile design while still adding a good amount of weight compared to brass weights with the adhesive backside ensuring easy mounting of the weight. The weight comes laser-engraved for easy identification.
Source: T-Works [rc-tworks.com]
JConcepts introduces this servo mount brace for the B6.3 line of vehicles. Constructed of light-weight aluminium, it has been a staple to racer’s vehicles going back to previous generation vehicles. The simple and sleek design with performance and tracking advantages have spoken volumes throughout the years on the racetrack. The mount fits snug inside the chassis servo mounting area increasing the support while the 2 screw mounting locations are beefy in design and zeroed in for a direct mount to the chassis. The brace has locations on each side for included 3x6mm set screws to help align and maintain servo position during racing conditions, crashes, and hard hits. The set screws are intended to touch-off against the servo case and provide additional support retaining the servo in the intended position which helps maintain consistent steering trim. The servo mount brace can be installed without any modifications or additional equipment in B6.3 vehicles. With a sleek wrap-around design, luster of aluminium, and etched JConcepts.net logo, the brace adds consistency, performance tune-ability with aesthetic appeal. Available in black or blue.
Source: JConcepts [jconcepts.net]
Associated release these new Factory Team parts, designed to add adjustability and increase the durability of your Team Associated car. Highly adjustable C and D arm mounts as well as rear hubs allow for fine tuning toe, anti-squat and roll centres to make your vehicle perform as desired on any surface you drive. All of these parts fit: the Pro2 SC10, DR10 RTR, DR10 Reakt Pro Mod RTR, SR10 RTR and RB10 RTR.
New for the Infinity IF14-2 and IF14-2 FWD from Creation Model comes three new option parts. First up for the FWD is the flex bridge graphite top deck that features the same adjustability offered on the IF14-2 and which allows you to tune the chassis flex of the rear section of the car. Next up, also for the FWD, is this upper arm mount upgrade set that allows you to adjust the camber link length and height to perfectly tune your setup for any conditions. Finally there is a new 4 degree hard c-hub set which by using it you will notice increased response and improved steering from the beginning to the middle part of the corner.
Pro-Line is ready to unleash high-performance PowerStroke shocks that have been specifically designed for your Traxxas MAXX. The shocks include big bore aluminium shock bodies with infinite spring pre-load adjustment, strong machined aluminium shock caps, beefy 5mm shock shafts and true dual-rate springs for a massive performance and durability upgrade over the stock shocks. All you need to do is fill the shocks with oil, install on your MAXX, and go.
JConcepts intends to start the new season with a fresh outlook while continuing a ‘Forward Pursuit’ in the RC industry. The team will be donning a fresh leather patch hat in 2022 thanks to a fresh new graphic design from the central Florida based company. Hats are everyone’s best friend, especially with a total of 4 different variations available. When it comes to the leather patched logo, the lightning bolts release from the centre of the design, stirring up quite a bit of emotion. The hard circle boundary allows plenty of flow for branding, factory push, and calendar racing year. Of course, World Champion wording signifies the ultimate success. The 4 hat styles include a black or grey flat-bill panel and black or grey/white round-bill mesh.
Creation Model have introduced 4 new Infinity titanium screws, the first of which is this UFO head M2.5x6mm screw. Machined from high quality 64 titanium material it can be used to attach the anti-roll bar holder of the IF14-2 and IF14-2FWD. The other 3 screws are slim head screws that come in M3x8mm, M3x10mm and M3x14mm. The M3x8mm replace the steel slim head screws used to mount the rear chassis stiffener on the IF14-2FWD these will reduce weight and allow for fine chassis flex tuning. The M3x10mm are a direct replacement of the steel rear body mount screws of the IF18-2 and IF15W. And finally the M3x14mm slim head screw replaces the steel slim head screws used in the installation of the IF18-2 front blocks. The wrench size used is 2.0mm, and can also be tightened with a firm torque.
View the slim head screws here
For the XB8, Xray have released these moulded carbon fibre chassis side guards. Carbon fibre side guards are stiffer in the longitudinal direction to improve stability but still allow for some chassis twist that can help generate traction. Moulded from high-quality carbon fibre, the side guards perfectly fit the chassis plate to seal against dirt and protect from side impacts. The set includes left and right side guards. The side guards fit XB8, XB8E, XT8, and XT8E from year 2016 onwards.
Source: Xray [teamxray.com]
