December 4, 2008

Hot Bodies Moorespeed 908 bodyshell

Hot Bodies, under the Moorespeed label, have released this new 908 bodyshell, which has been designed for 1/12th scale circuit racing. This totally new design was developed from the ground up to be the ideal bodyshell for a wide range of racers and tracks. The air rushing over the bodyshell starts at the ground-level splitter and is forced over the front wheels and around the closed cockpit by sculpted flow channels. Ridges over the front wheels disrupt the air just enough to break it loose over the wheel arches until it flows back down slightly over the middle section of the body. The closed cockpit area helps stabilize the air as it rushes over the midsection, which hugs the battery and electronics area of the car chassis as closely as possible. As the air meets the rear wheels, further ducting and vertical supports direct the air over the rear spoiler, where a huge amount of downforce is created. Molded from crystal clear polycarbonate, it features clear overspray film, a pre-cut vinyl window mask sheet, and a decal sheet with headlights and Hot Bodies logos. Also available in lightweight version.

Click here for more photos… content


December 2, 2008

Shepherd Velox 2009 Chassis plate

Team Shepherd have announced the release of the new 2009 chassis plate for the Velox. It features a cutout in the front into which an additional 30g weight can be mounted as well as 4 holes on the sides for an additional 70g of weight. By mounting up to 100g on the very bottom of the chassis the centre of gravity is much lower and the performance is increased. It is highly recommended to use the new chassis with the 30g front weight as it increases the stability of the chassis.

Click more to see the weights… content


November 28, 2008

Cube Racing Black Low Friction Spurs

Cube Racing have been in contact to tell us about their new low friction black spur gear series. These 64 pitch gears are available in 88T – 106T, are well balanced, light and because they are very low friction they are perfect for 1/10th touring, 1/12th pan car as well as 1/10th buggy.

Source: Cube Racing [cuberacing.net]


November 28, 2008

Capricorn CL-9TE On road engine

Italian company Capricorn RC have announced the upcoming release of their CL-9TE .21 circuit engine. Featuring revised internals, the piston and liner timing has been revised and optimized for high performance, while the crankshaft has been hand modified and polished. Supplied with rear ceramic bearings the engine also has a very efficient new red anodized cooling head.

Click here for more images… content


November 25, 2008

Carson 210mm Group C shell

Carson Model sport in Germany have sent us the release for their 210mm wide Group C shell. Designed to fit a number of Tamiya chassis’, including the TA05-IFS, TB03 & F103, as well as all 200mm pan cars it is made from high quality lexan and sold clear.

Source: Carson [carson-modelsport.com]


November 25, 2008

FXF conversion kit for HB Cyclone

We were contacted by the people behind FXF to tell us about a conversion set that they are making for the HB Cyclone. Made by a Thai company and based on HB Cyclone suspension, it made its debut at the IFMAR World Championship in RCS Thailand earlier this month. This chassis now claims to have symmetrical tweak from the new longer upper deck, as well as narrower bulkheads and a very low C of G.

Click here to see more close up photos… content


November 24, 2008

Xray Alu Anti-Roll Bar collars

Xray have released these aluminium anti-roll bar collars, that remove play from the front anti-roll bar wire, increasing cornering speed and stability. Suitable for all T2 cars the set consists of 2 collars and setscrews.

Source: Xray [teamxray.com]


November 24, 2008

H.A.R.D. H6 On road Starter box

H.A.R.D. Racing have released their great looking new H6 compact on road starter box, the next evolution of their Alpha starter. The H6 has been designed with improved performance, user friendly features and advanced circuitry which helps produce better torque when starting your 1/10th of 1/8th scale on road engines. Powered by 2 high torque 550 motors, the box casing is made from a lightweight aluminium that features simple to use adjustable brackets, which enable you to align your car perfectly in no time.

Source: H.A.R.D. [hard-racing.com]